Lewati ke isi

Commercial 4-In-1 Modular Combination Island Freezer

CECLE 4 In 1 Combine Island Freezer two styles to choose from

I. Product Overview

1. Basic Equipment Information

  • Product Name: Commercial 4-In-1 Modular Combination Island Freezer / Commercial Supermarket Modular Merchandising Island
  • Official Model Title: 4 In 1 Combine Island Freezer two styles to choose from
  • Available Styles & Exterior Models:
  • Section A: Contemporary minimalist profile with smooth flowing lines for expansive, uninterrupted sightlines.
  • Section C: Classic structured profile with bold contours, designed to blend seamlessly with various retail interior decors.
  • Combination Configurations & Sizing:
  • 4 In 1 (Front 1.85M + Middle 2.105M): Front end-cap unit (1.85m) + middle extension module (2.105m) modular configuration.
  • 4 In 1 (Front 1.85M + Middle 2.505M): Front end-cap unit (1.85m) + high-capacity middle extension module (2.505m) configuration.
  • Equipment Category: Commercial large-capacity modular horizontal deep-freeze island case with sliding glass doors.
  • Market Positioning: Tailored for fresh supermarkets, chain retail stores, frozen food specialty shops, butcheries, seafood counters, and cold-chain distribution hubs. Thanks to its 4-in-1 modular splicing design, it can operate as a freestanding 360° centerpiece island or be decoupled into parallel runs aligned with store foot-traffic aisles, significantly enhancing merchandising volume and shopping navigation.

Engineering & Manufacturing Highlights:

  • Modular Flexibility (Can be combined at will): Designed with precision modular framing, allowing end-cap curved cabinets and linear center modules to butt together seamlessly, adapting to varied retail aisle footprints and exhibition layouts with plug-and-play expandability.
  • Superior Moisture-Retention (Good moisturizing effect): Eliminating the surface-drying issues inherent to forced-air open curtain cases, this freezer utilizes a fully enclosed cabinet structure based on natural convective cold air descent. Air motion is gentle, keeping moisture locked inside delicate frozen doughs, dumplings, and raw meats to prevent freezer burn and weight shrinkage.
  • Hygienic & Food-Safe Shielding (Environmental protection and hygiene): Fitted with tightly sealed, heavy-duty tempered sliding glass lids that cut thermal exchange to save energy while shielding inventory against ambient dust, airborne droplets, and contact contamination, adhering to modern food hygiene standards.
  • Independent Low-Noise Hermetic Compressors (Low noise): Each modular segment is driven by its own dedicated hermetic compressor unit featuring high energy efficiency ratios and rapid temperature pulldown. Reinforced chassis vibration damping and acoustic baffle designs keep store noise levels to an absolute minimum.

2. Core Functions & Operating Principles

  • Modular Micro-Circulation & Dedicated Thermostat Control: Every spliced unit features an independent refrigeration circuit and precision microcomputer temperature sensor. Utilizing natural gravity-fed cold pooling principles, cold air distribution remains uniform across extensive multi-cabinet runs without thermal dead spots.
  • Intelligent Microcomputer Auto-Defrosting: Integrated electronic controllers track evaporator temperatures and initiate automated cyclic defrosting routines, preventing frost build-up while eliminating labor-intensive manual scraping.
  • High-Density Polyurethane Foam Insulation: Formed with high-pressure, zero-ODP cyclopentane polyurethane foaming. The high closed-cell density prevents thermal bridging and moisture ingress, sustaining sub-zero temperatures even during high summer shopping peaks.

3. Core Value: Why Choose This Equipment?

  • Dynamic Layouts Drive Higher Sales Per Square Foot: The 4-in-1 modular platform expands or contracts to match any floorplan, assembling into an eye-catching 360° display hub that draws foot traffic from all directions.
  • Drastically Cuts Inventory Shrinkage: Gentle, closed natural-convection chilling prevents drying, cracking, and oxidation of delicate frozen goods (such as dumplings, seafood, and sliced meats), typically generating enough inventory savings to offset acquisition costs early in operation.
  • Significant Energy Conservation: Compared to open-top display cases of equivalent merchandising area, enclosed sliding glass island freezers block over 60% of ambient heat load, yielding substantial utility cost savings each year.

II. Workflow & Standard Operating Procedures (SOP)

To ensure reliable, long-term operation and maximum cooling performance, store operations and maintenance personnel must adhere to the following standards:

1. Site Preparation & Pre-Installation Requirements (Key Success Factors)

  • Floor Flatness & Alignment: Modular combination units require a rigid, completely level floor. Level each section precisely using the adjustable base leveling feet before locking modules together and sealing the seams, ensuring smooth operation of the sliding glass lids.
  • Ventilation Clearance: Never obstruct compressor intake and discharge ventilation louvers with cartons or promotional displays. Maintain at least 6–8 inches (15–20 cm) of unobstructed airflow clearance.
  • Resting Protocol Upon Delivery: Following logistics transit via ocean container and flatbed truck, do not plug in or power on the unit immediately! Keep the unit upright on a level floor for at least 24 hours to allow displaced compressor oil to drain back into the sump.

2. Pre-Startup Inspection & Splicing Setup

  1. Align Front end-cap cabinets with Middle extension units per your floorplan, secure module alignment clamps, and engage base stabilizers.
  2. Verify electrical infrastructure: each modular compressor section must connect to its own dedicated, properly rated commercial grounded wall outlet. Never daisy-chain with multi-outlet power strips.
  3. Slide open the top tempered glass lids, remove internal protective foam, and inspect wire baskets and sliding tracks to ensure clean, frictionless motion.

3. Standard Operating Guidelines

  1. Empty-Load Pre-Cooling: Close all sliding lids, switch on power, and run empty for 2 to 3 hours. Load frozen products only after the digital display confirms stable deep-freeze storage temperatures.
  2. Respect the Load Line: Never stack merchandise above the inner wall Load Line mark. Overfilling blocks convective cold air blankets and risks product impact with the sliding lids.
  3. Strictly Prohibit Loading Warm or Ambient Items: Only pre-frozen goods should be loaded into the cabinet. Introducing large batches of ambient or warm products will cause severe temperature spikes and excessive frost accumulation.

III. Core Technical Specifications

Technical Specification Commercial Standard Configuration
Product Name Commercial 4-In-1 Modular Combination Island Freezer (Custom Splicing Series)
Official English Model Title 4 In 1 Combine Island Freezer two styles to choose from
Available Styling Profiles (Model) Section A / Section C (Two distinct aesthetic styles available)
Combination Sizing Options (Size) 4 In 1 (Front 1.85M + Middle 210.5M) / 4 In 1 (Front 1.85M + Middle 250.5M)
Modular Splicing Feature Can be combined at will; modular end-caps and middle units combine freely
Moisture Retention Good moisturizing effect; closed natural convection chilling, non-drying
Hygiene & Sanitation Environmental protection and hygiene; sealed glass lids block dust & droplets
Compressor Assembly Low noise hermetic compressor unit; independent modular design
Cooling Method Closed static natural convection deep freezing (superior moisture retention vs. air curtains)
Lid Construction High-strength, anti-fog, low-emissivity dual-curved tempered glass sliding doors
Cabinet Insulation High-density high-pressure eco-friendly polyurethane foam, thermal-break sealed
Interior Display Hardware Heavy-duty dip-coated / stainless steel divider grids and high-capacity wire baskets
Global Shipping Options DDP by sea to door (customs clearance & duties prepaid) / Freight truck

(Note: Large modular commercial freezer installations require stable commercial electrical circuits. Verify store power capacity prior to installation).

IV. Frequently Asked Questions (FAQ)

  • Q: Why are 4-in-1 combination island freezers preferred over traditional open air-curtain display cases in supermarkets?
  • A: While open air-curtain cases allow easy reach-in access, their forced air currents rapidly dehydrate frozen pastries, raw meats, and seafood, resulting in surface cracking, discoloration, and significant weight shrinkage. They are also vulnerable to airborne dust and droplet contamination. The CECLE 4-In-1 Combine Island Freezer uses enclosed sliding glass doors with gentle natural convection cooling, preserving product moisture while cutting electrical consumption by over 50%.
  • Q: What is the primary difference between Section A and Section C styles?
  • A: Both versions offer the exact same cooling output, modular splicing capabilities, and refrigeration hardware. The difference lies in exterior aesthetics: Section A features a sleek, rounded modern profile focused on fluid visual continuity, while Section C presents a structured, geometric industrial aesthetic. Retailers can select the profile that best complements their store interior and shelving lines.
  • Q: Does this combination island freezer require periodic manual ice scraping?
  • A: No. The unit features integrated microcomputer cyclic defrosting that manages minor frost buildup automatically. Daily maintenance only requires wiping the interior walls and sliding tracks with a clean, soft cloth during store replenishment windows. Avoid using hard or sharp tools against the interior walls.

V. Video Demonstrations & Operational References

Review the exterior modular assembly, smooth glide of the sliding lids, and expansive interior merchandising capacity of this commercial combination island freezer:

VI. Commercial Terms & Purchasing Guide

1. Heavy Commercial Logistics & Warranty

  • Turnkey International Freight:
  • DDP Ocean Freight Delivery: Due to the physical footprint and tempered glass components, units ship fully protected on heavy-duty export-grade solid wood skids wrapped in honeycomb buffering board and multi-layer pearl foam. We provide end-to-end customs-cleared, duty-paid door-to-door delivery (DDP) alongside local liftgate truck transport directly to your retail entrance.
  • Factory Warranty & Engineering Support: Core hermetic compressors are supported by a comprehensive manufacturer warranty. CECLE maintains an established commercial spare parts inventory and a veteran engineering support team, offering remote video assembly guidance, digital parameter calibration, and ongoing operational support.

2. Official Ordering & Inquiries